ISONEM ANTI-STAIN

ANTI-STAIN

It provides long-term cleaning and protection on all kinds of porous and absorbent surfaces on which it is applied, thanks to its high dirt-holding resistance. ISONEM ANTI-STAIN is water-based, one - component, and transparent. It does not spoil the appearance of the surface with its structure that does not form a film on the surface it is applied to. Dirt particles cannot adhere to the facade surface and the surface is easily cleaned of dirt with water, especially effortlessly with rainwater. It is applied indoors and outdoors in a short time, is not affected by UV rays, is economical and long-lasting. For ISONEM ANTI - STAIN, which can be applied to any painted or unpainted surface, vertical and horizontal, only the surface needs to be absorbent

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,00 ± 0,10

pH (25°C): 8.0 – 11.0

Viscosity (25°C, mPa.s): 0 - 500

Solvent: Water

Color: Transparent

Product consumption: 50 – 100 mL/m² (one layer application)

Paintable (Coverage) Area: 10-20 m²/1 L plastic can, 50-100 m²/5 L plastic can, 100- 200 m²/10 L plastic can

Documents of the ProductDocuments of the Product

It is applied to all kinds of absorbent surfaces such as plaster, concrete, gas concrete, screed and painted surfaces with an absorbent surface.

Surface preparation: If there are cracks or shield parts on the surface to be applied, they should be repaired, the area to be applied is oil, dirt, dust, etc. it should be cleaned of impurities. If the surface to be applied has been washed, it should be left to dry and the application should be made after the surface has dried. It is necessary that the surfaces to be applied must be absorbent, it is not suitable for non-absorbent surfaces.

Method of Application: ISONEM is thoroughly shaken and mixed in an ANTI-STAIN canister. Then, it is poured into a plastic bucket and fed thoroughly with the help of a brush to the prepared surface.

General Features

Fast Drying

B S1 do Fire Class

B S1 do Fire Class

UV Resistance

CONCRETE

WALL, STONE

WALL (Painted/Unpainted)

WOOD, PAPER, CARTON

TILE, CERAMIC, PORCELAIN

PLASTER

STEEL, METAL

Application: Horizontal / Vertical

Surface Humidity: Dry surface

Application Tools: Roller, brush, spray

Primer Usage: X

Primer Consumption: X

Product Usage: 1 Layer

Product Consumption: 50 – 100 mL/m² (1 layer application)

Between Two Coats: 1 Hour

Touch Dry: 1 – 2 Hours

Hard Dry: 24 Hours

Note : Drying times are approximate data, it may vary depending on ambient conditions.

The information given in this technical data sheet has been prepared according to our knowledge, experiment results, and experiences. The correct and successful implementation of our products is completely beyond our control and responsibility. For this reason, our responsibility is limited to the quality of our product only, and this manual overrides all previous technical statements, descriptions and label information.

 

Packaging: 1, 5, 10 L in PE can

Storage temperature: 5 - 35 °C

Shelf life: 24 months from date of production if stored in original, unopened, undamaged packages.

Storage condition: Store tightly closed in a dry and cool place.

A IMPORTANT

The surface should be protected from rain, water, mechanical loads and impacts for 24 hours during and after the application.
 

APPLICATION CONDITIONS and RISKS

The application surface must be clean and free from all impurities like dirt, oil, and mud. Swelling parts should be scraped thoroughly and the surface should be dry.

Other ISONEM products recommended:  X

Application temperature: It should be applied between 5-35 °C.

...
Share this product:
x